Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - sodjer

Pages: [1] 2
Thank you gearmaker

Workspace, tools, machinery, and manufacturing / Juki 1900 EPROM
« on: July 30, 2020, 03:49:56 AM »
Hi guys, I am looking for help .
I cooked the main board on my juki 1900 bartacker ( 2000 model )
I got it up and running  but, I am now getting an E1 fault , I have tried all fixes .
I was wondering if I could kill two birds with one stone here and buy an EPROM for the machine with up dated pattern ( I know a guy was selling them on dropzone , I have contacted him , but he is not answering ) does any body know another source ?? Thanks in advance Davy 

Materials science / Re: Acronym vs Centurion
« on: June 30, 2020, 04:07:05 AM »
Honeywell have stopped making centurion in the US .

Asset exchange / Re: WTB: full roll of 1000D Coyote Brown Cordura
« on: April 21, 2019, 12:55:06 AM »
Hi victor ,try Dave at contact left.i am sure he has a few rolls happy Easter

Materials science / Re: Heat forming
« on: February 17, 2019, 01:42:43 AM »
I ve already went down that road with plasti-dip,the product is good , it gave reasonable results ,but drying times interfered with production .
I have done experiments with irons ( domestic and soldering ) and believe if I can hit the right temp range I can make a heated press that will give repeatable results.
Failing that ,I have a small manual injection moulding unit , I will try something similar to the ends of the Spanish buckle.

Materials science / Heat forming
« on: February 15, 2019, 03:21:53 PM »
I am working on a project just now ,I am not happy with the finish in the 1 inch( doubled) webbing tabs.
I was thinking of making a heated mould/pattern that would finish the tabs better , has any body tried this or has any experience of heat forming or finishing webbing without stitching on end plastic tabs?

Introductions / Re: Hello from Liverpool
« on: February 10, 2019, 02:51:54 AM »
Hi dave , it is a small world . Glad to see you here ,and welcome. Davy

Hi Corvus ,I had the same problem ,with the same machine .only difference mine was intermittent.
I could run it all day without problem ,next day I had to rethread after 5 tacks,next day good again .
I looked at my threading ,I changed needles ,even room temp ( it seemed to happen when it was cold in the workshop )
I changed the company who supplied my thread and I havenít had any more trouble .

Vendors and sources / Re: first-spear tubes
« on: October 28, 2018, 12:45:22 PM »
sorry guys I posted this already in the wrong part but it's still relevant

Materials science / Re: PC buckles, ROC or NM Tactik
« on: October 28, 2018, 12:34:48 PM »
has anybody tried these
I can vouch for contact left ,quick and efficient,I tried the ROC on a job and didn't really 
like them

I have been watching this article with interest ,at present I am cutting 2 inch straps by the hundred and it tedious.
I also just bought a cheapo Chinese laser cutter ( to learn with ) when setting it up I cut through a 40 mm piece of webbing and it cut it quick and nice ( and square ) would it be possible to make a strap cutter using one of these machines .
The y axis to cut across and the x Axis to run the feed rollers

Hey nick ,if you find you need ally angle ,box section or item profile give me a shout  Davy

Workspace, tools, machinery, and manufacturing / Re: reese s2
« on: September 07, 2018, 08:36:34 AM »
hey guys ,thanks for the advice ,I bit the bullet and went for a juki 1900 ah ,I got a good price on it and I get it next Friday .

Workspace, tools, machinery, and manufacturing / Re: reese s2
« on: August 15, 2018, 01:42:41 PM »
thanks W24 ,I am now looking at a brother B430-2 in 42 stitch ,I hope that will cut the mustard ,any vices on this machine? Davy

Workspace, tools, machinery, and manufacturing / reese s2
« on: August 08, 2018, 01:01:47 PM »
hi all , I have the chance of getting hold of an old reese s2 bartacker ,any body have experience of these old war horses?

Pages: [1] 2