Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages -

Pages: [1] 2 3 ... 18
This facebook group is uh-mazing for stuff like that-

Robert Collier of Collier Equipment is an admin.  Very knowledgeable and helpful dude.

Good luck.

Web presence / Re: Trademarking a brand name?
« on: July 18, 2020, 07:54:03 PM »
How much money do you have to litigate brand name infringement?

That was a good article. So say I didn't register the name and someone else goes and registers the name I'm using, I would have no power to fight back, correct?

Contact an attorney.

The Boardroom / Re: Would you use slave labor or prison labor?
« on: July 17, 2020, 04:08:36 PM »

"Lawyers under the oversight of then-Attorney General of California Kamala Harris argued in 2014 against the release of nonviolent criminals because they wanted to keep them for cheap labor. "

“That’s the ones you can work,” Prator said of the people who could be soon be let go under the plan. “That’s the ones that can pick up trash, the work release programs. But guess what? Those are the ones [the state is] releasing.” He added, “In addition to the bad [prisoners], they’re releasing some good ones that we use every day to wash cars, to change oil in our cars, to cook in the kitchens, to do all that where we save money—well, they’re going to let them out.”

Every sound bite or statistic can be skewed to show whatever.  This is offered for what it is.

Web presence / Re: Trademarking a brand name?
« on: July 17, 2020, 12:32:24 PM »
How much money do you have to litigate brand name infringement?

Platforms / Re: Outer Belt 04 MOLLE Micro PALS Shooter's Belt
« on: July 04, 2020, 12:58:58 PM »

Introductions / Re: New Guy From Virginia
« on: June 24, 2020, 07:54:01 PM »
Welcome aboard.

Introductions / Re: New member from California
« on: May 21, 2020, 02:37:23 PM »
Welcome aboard.  Thanks for participating.

Concept, design, and engineering / Re: IR Patches
« on: February 29, 2020, 04:10:19 PM »
Has anyone here ever produced IR patches/badges?
Im looking to produce some but unsure where to start.


Post an intro.

Welcome aboard!

Tutorials and techniques / Re: WTFiles: Open Source Zipper Guide
« on: February 04, 2020, 03:27:56 PM »
Post an intro.

Huh.. I might grind out a piece of a seam guide to fit the same purpose.

The question is, will this stop me from sewing zippers inside-out or upside-down. Or both inside-out and upside-down at the same time? I still mess them up from time to time...

Concept, design, and engineering / Re: swivel/rotating buckles in tan499
« on: February 03, 2020, 04:58:27 PM »
Post an intro.

Trying to prototype a MOLLE drop leg thigh rig in tan 499. I've been searching and can't find the nifty center release circular buckles in tan499 for the life of me. You know, these kind:

I'd hate to have to put a black buckle on an otherwise tan499 rig. I suppose I could use a standard side release buckle, but then it doesn’t swing with the operator's leg movements as well.

Any help/suggestions would be appreciated.

Introductions / Re: Newbie here! Hi there from Ontario Canada
« on: December 27, 2019, 11:53:17 AM »
Welcome aboard.  Thanks for your participation.

The Boardroom / Buying a building
« on: December 16, 2019, 05:29:26 PM »
The commercial loan broker inspects your P&L, bank statements, and account history.  You're approved for a $750,000 loan.  You need 20% down.

Your $250k home is paid off.  Would you borrow $150,000 against your home to buy a commercial building?

The Boardroom / Would you use slave labor or prison labor?
« on: December 16, 2019, 02:27:08 PM »
Are there any circumstances under which your brand would knowingly use slave labor or prison labor to make parts?  Do you discern between slave labor and prison labor?

Vendors and sources / Re: Source for 3/8inch or 10mm Webbing in Ranger Green
« on: September 09, 2019, 03:52:13 PM »
Thank you very much for taking a moment to share your solution :-)

Pages: [1] 2 3 ... 18